professionalnero.blogg.se - Hyperterm right click

#HYPERTERM RIGHT CLICK SERIAL#
#HYPERTERM RIGHT CLICK DRIVER#
#HYPERTERM RIGHT CLICK SOFTWARE#
#HYPERTERM RIGHT CLICK WINDOWS 7#

This is either a float with period separator, or integer value as appropriate. VALUE contains the numerical value corresponding to value being measured. PosiTector SST Conductivity1 - Referenced conductivit圜onductivity2 - Sample conductivityTemperature1 - Reference temperatureTemperature2 - Sample temperatureDuration - DurationVolume - Sample VolumeSurface Density - Surface Density PosiTector SHD HD - ShoreD hardnessHA - ShoreA hardnesst - Duration in seconds PosiTest AT-A Pressure - PressureDuration - DurationIn Hold - Number of seconds into hold time when pull endedStatus - Pull status VALUE contains status of the pull 0 = No Pull occurred 1 = Pull occurred 2 = Pull cancelledLimit - Maximum pressureHold_Time - Number of seconds to hold LimitDolly_Size - Dolly size in mmRate - Rate to increase pressureP/F - Pass / Fail status VALUE: 0 = Fail 1 = Pass PosiTector RTR H/HL - Height / Linearized HeightPd - Peak Density PosiTector DPM Ta - Air temperatureTs - Surface temperatureTd - Dew Point temperatureTs-Td - Delta temperatureTw - Wet bulb temperatureRH - Relative humidity PosiTector 200 Layer_1 - Layer 1 thicknessLayer_2 - Layer 2 thicknessLayer_3 - Layer 3 thickness (PosiTector 6000 FNDS Duplex probe)Zn - Zinc layer thickness. (PosiTector SPG, RTR)N - Non Ferrous thickness.

(PosiTector 6000, UTG, 200, PC)Roughness - Roughness measurement. LABEL will display one of the following values: LABEL describes the data type being displayed. The fields are: LABEL VALUE UNIT MATL PosiTector 6000 Example: Thickness 50 microns F A READING is output using the following layout: VALUE1 CRVALUE2 CR.VALUEN CRĮach VALUE# consists of 3 or 4 fields. If not, ensure the gage is powered-on and connected to the computer.įor the purposes of this document, the following conventions are used: STX = ascii STX character (0x02)EOT = ascii EOT character (0x04)CR = ascii carriage return character (0x0a)Įach reading is output using the following layout: STX CRREADINGEOT CRĪ READING may consist of multiple values, for example a PosiTector DPM with 5 or 6 values.

#HYPERTERM RIGHT CLICK SERIAL#

Step 4: Select Device Manager from within the Windows Control Panel CDC Serial Should be listed under Other Devices. Step 3: Connect the Gage to the computer using the supplied USB cable.

#HYPERTERM RIGHT CLICK DRIVER#

Step 2: Download and extract the gserial driver (required for Step 4). Image of 3 gage body screenshots showing the menu structure for setting up the gage to Stream Measurement Data

Step 1: Power on the PosiTector and access the menu by pressing the center navigation button (menu button on PosiTest AT-A). Setup the Gage to Stream Measurement Data While written for Bluetooth, the same step-by-step instructions apply to serial communications over USB. See our technical note for more information on setting up serial communications with Proficient and WinSPC. This could mean controlling peripherals attached to the serial ports, bulletin board systems, remote computers networked with the home computer, and so on. Proficient (by InfinityQS) and WinSPC (by DataNet systems) are two popular options. The HyperTerminal is a convenient preinstalled Windows component that was used to communicate with the external world.

#HYPERTERM RIGHT CLICK SOFTWARE#

Any software that accepts data via a serial interface can be configured to accept the PosiTector data stream.Ī common application for serial streaming is PC-based statistical process control (SPC) software.

#HYPERTERM RIGHT CLICK WINDOWS 7#

The included example uses Windows HyperTerminal ( not included in Windows 7 and newer) for data collection. is a quick hack that could do the job for now.PosiTector Advanced (serial numbers 784000 and greater) and PosiTest AT-A instruments (with a color display) allow live streaming of measurement values to a USB connected computer. is the best way to go (it will also fix other bugs like #116), but it will need definitely more work, while 2.

Temporarily give focus and enable contenteditable on the terminal element to allow pasting without messing with text selection issues.

This would need non-native selection handling though ( Add textarea back and support IMEs #175 (comment)).

Temporarily move the textarea element below the mouse cursor on right click ( Add textarea back and support IMEs #175 (comment)).

This could be solved in the following two ways (additional ideas are always welcome though) This regression was caused after #175, since we moved input handling to a textarea instead of xterm itself.